1/4 ultra-low ohmic chip resistors for current detection pmr series www.rohm.com c 2014 rohm co., ltd. all rights reserved. 2014.06 - rev.d da t asheet ? features 1) ultra low-ohmic resistance range (1m ? ~ ) 2) improved current detection accu racy by trimming-less structure. 3) special low resistance temperature coefficient. 4) the unique chip structure minimizes t hermal stress during temperature cycling, resulting in greater reliability. 5) rohm resistors have obtained is o9001 / iso / ts16949 certification. 6) corresponds to aec-q200. (pmr50 / 100) ? products list operating temperature range ( c) rated power (70 c) (w) PMR006 0603 0.1 1608 3216 5025 pmr03 pmr18 pmr50 0.25 1 1 ? 55 to + 155 pmr01 1005 0.2 3225 pmr25 1 2012 pmr10 0.5 6432 0201 0603 1206 2010 0402 1210 0805 2512 pmr100 2 : under development ? : 150ppm / c ( 1m , 2m only) design and specifications are subject to change without notice. carefully check the specification sheet supplied with the product before using or ordering it. temperature coefficient (ppm / c) resistance tolerance (%) j( 5%) 0 to 300 j( 5%) 0 to 200 f( 1%) j( 5%) 0 to 150 f( 1%) j( 5%) 100 f( 1%) j( 5%) 100 g( 2%) f( 1%) j( 5%) 150 f( 1%) j( 5%) 100 f( 1%) j( 5%) 100 ? resistance range 10m 10m 10m 2,3,4,5,6,7,8,9,10m 1,2,3,4,5,6,7,8,9,10m 1,2,3,4,5m 1,2,3,4,5,6,7,8,9,10m 1,2,3,4,5,6,7,8,9,10m size (mm) (inch) part no. ? part number description special part code resistance tolerance pmr (ultra-low ohmic chip resistors for current detection) j f,g resistance tolerance resistance value( ) 1l0 1l00 006 (0603 [0201] ) 01 (1005 [0402] ) 03 (1608 [0603] ) 10 (2012 [0805] ) 18 (3216 [1206] ) 25 (3225 [1210] ) 50 (5025 [2010] ) 100 (6432 [2512] ) u : 5 to 10m v : 1 to 4m 2 5 hp z m pr vl 2 0 f ( 1% ) g ( 2% ) j ( 5% ) j paper tape (4mm pitch) ezp pmr18 5,000 paper tape (4mm pitch) ezp pmr10 5,000 paper tape (4mm pitch) ezp pmr03 5,000 paper tape (2mm pitch) mzp pmr01 10,000 paper tape (2mm pitch) yzp PMR006 15,000 embossed tape (4mm pitch) hzp pmr25 2,000 embossed tape (4mm pitch) hzp pmr50 2,000 embossed tape (4mm pitch) hzp pmr100 2,000 1m 2l0 2l00 2m 3l0 3l00 3m 4l0 4l00 4m 5l0 5l00 5m 6l0 6l00 6m 7l0 7l00 7m 8l0 8l00 8m 9l0 9l00 9m 10l 10l0 10m part no. size (mm [inch]) packaging specifications code packaging specifications code part no. quantity / reel resistance code, 3 or 4 digits. nominal resistanc e
2/4 data sheet pmr series www.rohm.com c 2014 rohm co., ltd. all rights reserved. 2014.06 - rev.d ? chip resistor dimensions and markings there are four digits used for the calculation number "l" is used for the decimal point of m ??? ex.) 2m ? =2l00 10m ? =10l0 lw t a c (unit : mm) PMR006 0603 0.6 0.05 0.3 0.05 0.23 0.05 ?? no pmr25 3225 3.2 0.2 2.5 0.2 0.52 to 0.32 ? 0.15 0.5 0.2 yes pmr50 5025 5.0 0.2 2.5 0.2 0.52 to 0.32 ? 0.15 0.5 0.2 1.95 0.2 yes pmr100 6432 6.4 0.25 3.2 0.25 0.52 to 0.32 ? 0.15 0.5 0.25 2.65 0.25 yes 1.95 0.2 b 0.15 0.05 pmr01 1005 1.0 0.05 0.5 0.05 0.25 0.1 ?? no 0.3 0.1 pmr03 1608 1.6 0.15 0.8 0.15 0.25 0.1 ?? no 0.35 0.15 pmr10 2012 2.0 0.15 1.2 0.15 0.42 to 0.28 ? 0.15 ?? yes 0.75 to 0.35 ? 0.25 pmr18 3216 0201 1210 2010 2512 0402 0603 0805 1206 3.2 0.15 1.6 0.15 0.42 to 0.28 ? 0.15 ?? yes 1.2 to 0.5 ? 0.25 1.85 to 0.9 ? 0.2 2.3 to 1.1 ? 0.25 1.0 to 0.8 ? 0.2 : under development ? : each value range varies with the resistance. please contact a rohm sales representative for further details. part no. (mm) marking existence (inch) ? land pattern example b d a land c a pmr01 pmr50 pmr100 0.5 1.8 1.2 (1m ) 2.4 (2,3,4,6m ) 3.0 (5,7,8,9,10m ) 6.8 (1m ) 7.6 (2 to 10m ) 3.4 (1m ) 3.8 (2 to 10m ) 2.8 (1m ) 2.6 (2,3,4,6m ) 2.3 (5,7,8,9,10m ) b 1.8 6.0 c 0.5 2.8 d 0.65 pmr03 0.5 2.5 0.9 1.0 pmr10 0.8 3.4 1.3 1.3 pmr18 1.0 4.0 1.8 1.5 pmr25 1.0 4.0 2.8 1.5 2.1 (unit : mm) dimensions part no. l l a c a b b b b b w w t t 2l00 2l00 ? PMR006 / 01 / 03 / 10 / 18 ( top) ( bottom) (top) (bottom) ? pmr25 / 50 / 100
3/4 data sheet pmr series www.rohm.com c 2014 rohm co., ltd. all rights reserved. 2014.06 - rev.d ? derating curve when the ambient temperature ex ceeds 70c, power dissipation must be adjust ed according to the derating curves below. PMR006 / 01 / 03 / 10 / 18 / 25 / 50 / 100 0 20 40 60 80 100 ? 55 0 70 100 155 percent rated power (%) ambient temperature ( c) ? characteristics (pmr01 to 100) resistance (2.0% + 0.0005 ) (1.0% + 0.0005 ) (3.0% + 0.0005 ) see p.1 see p.1 20 c measuring method : measure under terminations by 4 probes. (under terminations) no remarkable abnormality on the appearance. a new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. without mechanical damage such as breaks. compliance standard(s) : iec60115 ? 8 jisc 5201 ? 8 measurement : + 20 / ? 55 / + 20 / + 125 c (3.0% + 0.0005 ) (3.0% + 0.0005 ) (0.5% + 0.0005 ) (1.0% + 0.0005 ) ? soldering condition : 260 5 c duration of immersion : 10 1s 40 c, 93%rh (relative humidity) test time : 1,000h to 1,048h 70 c rated power 1.5h : on ? 0.5h : off test time : 1,000h to 1,048h 155 c test time : 1,000h to 1,048h 23 5 c, immersion cleaning, 5 0.5min solvent : 2 ? propanol test temp. : ? 55 c to + 125 c 5cycle rosinethanol : 25% (weight) soldering condition : 235 5 c duration of immersion : 2.0 0.5s rated power 2.5, 2s probes endurance at 70 c endurance bend strength of the end face plating resistance to solvent overload solderability resistance to soldering heat rapid change of temperature damp heat, steady state test items test conditions resistor type guaranteed value variation of resistance with temperature ? chip weight (typical value) mg/pc 0.829 2.12 7.08 (2m ) 6.77 (3 to 5m ) 4.61 (6 to 8m ) 3.73 (9 to 10m ) 15.1 (1 to 2m ) 14.3 (3 to 6m ) 9.77 (7 to 8m ) 8.01 (9 to 10m ) 32.5 (1m ) 28.1 (2 to 3m ) 16.9 (4 to 5m ) 45.2 (1 to 2m ) 40.9 (3 to 5m ) 25.0 (6 to 10m ) 73.8 (1 to 2m ) 66.9 (3 to 5m ) 40.3 (6 to 10m ) pmr01 pmr03 pmr10 pmr18 pmr25 pmr50 pmr100 parameter unit weight
4/4 da t asheet pmr series www.rohm.com c 2014 rohm co., ltd. all rights reserved. 2014.06 - rev.c ? tape dimensions ? paper tape ? embossed tape a 0 p 1 p 0 p 2 b 0 f w t 2 e d 0 p 0 p 2 p 1 e f w t 2 d 0 a 0 b 0 base paper (bottom tape) components cavity top tape 0.7 0.1 1.2 0.1 1.95 + 0.1 ? 0.05 3.5 + 0.15 ? 0.05 (unit : mm ) w part no. f e a 0 b 0 8.0 0.3 pmr01 3.5 0.05 1.75 0.1 0.95 0.1 1.75 0.1 8.0 0.3 pmr03 3.5 0.05 1.75 0.1 1.45 + 0.2 ? 0.1 2.3 + 0.2 ? 0.1 8.0 0.3 pmr10 3.5 0.05 1.75 0.1 8.0 0.3 pmr18 3.5 0.05 1.75 0.1 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 2.0 0.05 max 1.1 max 1.1 d 0 part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 2.0 0.05 1.5 + 0.1 0 2.0 0.05 max 1.1 4.0 0.1 4.0 0.1 1.5 + 0.1 0 2.0 0.05 max 1.1 4.0 0.1 4.0 0.1 4.0 0.1 3.0 0.1 3.5 0.1 3.5 0.2 6.7 0.2 (unit : mm ) w part no. f e a 0 b 0 8.0 0.3 pmr25 3.5 0.05 1.75 0.1 2.9 0.2 5.3 0.2 12.0 0.3 pmr50 5.5 0.05 1.75 0.1 12.0 0.3 pmr100 5.5 0.05 1.75 0.1 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 2.0 0.05 max 1.1 max 1.1 d 0 part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 4.0 0.1 1.5 + 0.1 0 2.0 0.05 max 1.1 4.0 0.1 4.0 0.1 4.0 0.1 pmr01 pmr03 pmr10 pmr18 pmr25 pmr50 pmr100 ? reel dimensions a part no. b c d (unit : mm ) 13 0.2 PMR006 pmr01 pmr03 pmr100 9 + 1.0 0 13 + 1.0 0 pmr18 pmr25 pmr50 pmr10 0 2 0 4 0 6 0 8 0 2 0 4 0 6 0 8 c abd label 180 0 ? 1.5 60 + 1.0 0 : under development according to eiaj et-7200 b
r1 102 a www .rohm.com ? 2014 rohm co., ltd. all rights reserved. notice rohm c u stomer support sys tem h ttp://w w w . r ohm .com/con tact/ thank you for your accessing to rohm pr oduct informations. mor e detail pr oduct informations and catalogs ar e available, please contact us. notes the inf or mation contained herein is subject to change without notic e . bef ore y ou use our p r o d u c t s , ple a s e c o n t a c t o u r s a l e s r e p r e s e n t a t i v e and v e r i f y the l a test specifica- tions : althoug h r o h m is c o n t i n uousl y w o r king t o impro ve p roduct r elia bility and quality , semicon- duc tors c an brea k do w n and mal f unction due to va r ious f actor s . the ref o r e , i n ord e r to p r e ve n t per sonal i n jur y or fire a r isin g f rom f a ilure , please tak e saf ety meas ure s suc h a s c o m plying wit h the der ating cha r a cte r istics , imple menting redundant and f ire p r e ve nti o n d e s i g n s , and u tilizing bac k ups a nd f ail- saf e p rocedures . r o hm shall h a ve no responsibility f or an y damages ar ising out of the use of our p oducts beyond the r ating specified b y r ohm. examples of application circuits , circuit constants and an y other inf or mation contained herein are pro vided only to illustr ate the standard usage and oper ations of the products . the per iphe r al conditions m ust be tak en into account when designing circuits f or mass production. the technical inf or mation specified herein is intended only to sho w the typical functions of and e xamples of application circuits f or the products . r ohm does not grant y ou, e xplicitly or implicitl y , an y license to use or e x ercise intellectual prope r ty or other r ights held b y r ohm or an y other par ties . r ohm shall ha v e no responsibility whatsoe v er f or an y dispute ar ising out of the use of such technical in f or mation. the products are intended f or use in gene r al electronic equipment (i.e . a v/o a de vices , comm uni- cation, consumer systems , gaming/ente r tainment sets) as w ell as the applications indicated in this document. the products specified in this document are not designed to be r adiation tole r ant. f or use of our products in applications requi r ing a high deg ree of reliability (as exemplified bel o w), please contact and consult with a r ohm representati v e : tr anspo r tation equipment (i.e . cars , ships , tr ains), pr imar y comm unication equipment, tr affic lights , fire/cr ime pre v ention, saf ety equipment, medical system s , ser v ers , solar cells , and po w er tr ansmission system s . do not use our products in applications requir ing e xtremely high reliabilit y , such as aerospace equipment, n uclear p o w er control systems , and submar ine repeater s . r ohm shall ha v e no responsibility f or an y damages or inju r y ar ising from non-compliance with the recommended usage conditions and specifications contained herein. r ohm has used reasona b le care to ensur the accur acy of the inf or mation contained in this document . ho w e v er , r ohm does not w arr ants that such inf or mation is error-free , and r ohm shall ha v e no responsibility f or an y damages ar ising from an y inaccu r acy or mispr int of such inf or mation. please use the products in accordance with an y applica b le en vironmental la ws and regulation s , such as the rohs directiv e . f or more details , including rohs compatibilit y , please contact a r ohm sales office . r ohm shall ha v e no responsibility f or an y damages or losses resulting non-compliance with a n y applica b le la ws or regulation s . when pro viding our products and technologies contained in this document to other countr ies , y ou m ust abide b y the procedures and pro visions stipulated in all applica b le e xpor t la ws and regulation s , including without limitation the us expor t administr ation regulations and the f oreign exchange and f oreign t r ade act. this document, in par t or in whol e , ma y not be repr inted or reproduced without pr ior consent of r ohm. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14)
|
